Topcom Babyviewer 4500 Guide de l'utilisateur télécharger pdf (Page 5)

Babyviewer 4500

ENGLISH

9 Installing the Babyviewer 4500

9.1 Fine tuning

• Place the camera in a convenient location, point the lens of

the camera to the observation area.

• Adjust the angle by rotation the camera.

10 Operation and use

10.1 Switching the baby unit and parent unit on

and off

– Press the on/off switch to switch on the parent

unit. The display is activated.

– Slide the on/off switch up to switch on the baby

unit. The on/off LED is activated.

– Press the on/off switch to switch off the parent

unit (press and hold until the display goes blank).

– Slide the on/off switch down to switch off the

baby unit.

10.2 Checking the connection between the parent

unit and the baby unit

You should always check the wireless connection when you use

the babyphone for the first time.

– Put the parent unit in the same room as the baby unit,

separated by at least two metres.

– Switch on both devices. The parent unit will try to

establish a connection with the baby unit.

– The display of the parent unit will show the captured

image from the baby unit after the connection has been

established (monitor mode).

– The sounds picked up by the microphone are

reproduced by the parent unit.

– The volume of the reproduced sound is indicated by the

volume LED’s at the top of the parent unit.

The higher the volume, the more LED’s are on.

– If no connection is established, the out of range icon is

displayed and a beep is audible.

10.3 Out of range indication

The maximum range between the parent- and baby unit is 300

meter in open area. Different factors, such as bricks and plaster

walls, will reduce the range. Moreover, reinforced concrete floors

will influence the range tremendously.

In a residence, normal operating range is up to 50 meters and 2

floors.

– If the connection is interrupted, the out of range icon is

displayed and a beep is audible.

– Reduce the distance between the parent and baby units

until a new connection is established.

10.4 Setting the reproduction volume of the

parent unit

There are 5 volume levels.

– Press button to increase the volume.

– Press button to decrease the volume.

10.5 Setting the parent unit display brightness

When the display in on.

– Press the menu button once. The Brightness

icon is displayed.

– Press the up or down button to select the

desired brightness (5 steps).

– Press the menu button to confirm.

– After 10 seconds the parent unit will switch back to

monitor mode.

10.6 Temperature indication

When the display is on, the baby’s room temperature is displayed

in the right lower corner.

To set the temperature unit:

– Press the menu button twice. The temperature

icon is displayed.

– Press the up or down button to °C

(Celsius), °F (Fahrenheit) or “OFF”, to switch the

temperature indication off.

– Press the menu button to confirm.

– After 10 seconds the parent unit will switch back to

monitor mode.

10.7 Talking with your baby

You can use the parent unit to talk with your baby.

– Press the Talk button on the parent unit and hold

it pressed.

– Hold the parent unit vertical with the microphone

approximately 10 cm from your mouth, and speak into

the microphone.

– Release button when you have finished talking.

10.8 Playing a lullaby

There are 5 pre-programmed lullabies that you can play on the

baby unit.

– To play the currently selected lullaby or stop playback,

press the play button on the baby unit.

– To select a different lullaby, repeatedly press the lullaby

button until the desired lullaby is selected. The

lullaby icon will display the selected lullaby (1 to 5). If no

number is displayed, next to the lullaby icon, all songs

will be played successively.

When the lullaby starts playing, you have 10 seconds to set the

volume of the lullaby.

– Press the up button to increase the volume or

the down button to decrease the volume.

10.9 Switching the night light on and off

– Press the menu button 3 times. The night light

icon is displayed.

– Press the up or down button to switch

the night light “ON” (night light is on) or “OFF”.

– Press the menu button to confirm.

– After 10 seconds the parent unit will switch back to

monitor mode.

10.10 Voice activated transmission (VOX)

During night and to save energy, the Babyviewer 4500 can be set

in VOX mode.

In VOX mode, the display will be activated as soon as the

microphone of the baby unit will capture sound.

You can set the sound detection sensitivity (VOX) of the

babyphone. If the sensitivity is set to high, the baby unit will pick

up weaker sounds.

– Press button 4 times. “VOX” is displayed.

– Repeatedly press button or to set the

VOX sensitivity.

CAUTION

Do not place the camera and wires within the baby’s reach!

Fix the camera at least 1 meter away from the baby.

The parent unit will try to establish a connection

with the baby unit. If captured image from the

camera is displayed, a connection has been

established.

Allow your baby to get used to the talk function

before you use it in practice.

• 10 seconds after starting or selecting the

lullaby, the parent unit will return to monitor

mode. The up button and down

button can than only be used to set

the volume of the parent unit.

• To set the volume of the lullaby in monitor

mode, switch the lullaby off and on using

the button first before selecting the

volume.

16 17

PTT

PTTPTT

1 2 3 4 5 6 7 8 9 10 ... 83 84

Commentaires sur ces manuels

Pas de commentaire

Topcom Babyviewer 4500 Guide de l'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Babyphones Topcom Babyviewer 4500